Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-620 Exam - Topic 1 Question 111 Discussion

Refer to the exhibit.The Cisco ACI fabric is built with L20ut to the N9K1 and N9K2 switches. The switches run the RSTP protocol. The requirement is for the Cisco ACI fabric to detect 5 from the N9K and for the fabric to be protected against loops. Which set of actions must be taken to meet the requirements?
D) Configure the N9K STP link type as a shared link. Enable MCP on ACI globally.
A) Configure the N9K STP link type as point-to-point link. Enable MCP on ACI globally.
B) Configure the N9K STP link type as a point-to-point Enable MCP on the ACI leaf interfaces.
C) Configure the N9K STP link type as a shared link. Enable MCP on the ACI leaf interfaces.

Cisco 300-620 Exam - Topic 1 Question 111 Discussion

Actual exam question for Cisco's 300-620 exam
Question #: 111
Topic #: 1
[All 300-620 Questions]

Refer to the exhibit.

The Cisco ACI fabric is built with L20ut to the N9K1 and N9K2 switches. The switches run the RSTP protocol. The requirement is for the Cisco ACI fabric to detect 5 from the N9K and for the fabric to be protected against loops. Which set of actions must be taken to meet the requirements?

Show Suggested Answer Hide Answer
Suggested Answer: D

by Kristofer at May 06, 2026, 02:04 PM

Limited Time Offer

25%

Off

Get Premium 300-620 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Paul
3 days ago
Exactly! B is tailored for the setup shown.
upvoted 0 times
...
Teddy
8 days ago
I feel like A might overlook some details.
upvoted 0 times
...
Lauran
13 days ago
Still, B is more specific to the N9K switches.
upvoted 0 times
...
Charlie
19 days ago
True, but A covers all bases.
upvoted 0 times
...
Paul
24 days ago
But wouldn’t enabling MCP on leaf interfaces (B) be safer?
upvoted 0 times
...
Teddy
29 days ago
I’m leaning towards A. Global MCP could be more effective.
upvoted 0 times
...
Lauran
1 month ago
I agree, B seems right. Point-to-point is crucial.
upvoted 0 times
...
Charlie
1 month ago
This question is tricky! I think option B makes sense.
upvoted 0 times
...
Annamae
1 month ago
D) sounds risky, better stick with point-to-point configurations.
upvoted 0 times
...
Jennie
2 months ago
C) won't work because shared links are not ideal for this setup.
upvoted 0 times
...
Shaunna
2 months ago
Isn't it surprising that RSTP can handle loops so well?
upvoted 0 times
...
Kenny
2 months ago
I disagree, I think B) makes more sense for leaf interfaces.
upvoted 0 times
...
Fidelia
2 months ago
A) is the right choice for point-to-point links.
upvoted 0 times
...
Dolores
2 months ago
I’m leaning towards option B, but I’m a bit confused about the shared link configuration.
upvoted 0 times
...
Stevie
4 months ago
I feel like enabling MCP globally might be too broad for this scenario.
upvoted 0 times
...
Linwood
4 months ago
I think we practiced a similar question where enabling MCP on ACI leaf interfaces was the right move.
upvoted 0 times
...
Melodie
4 months ago
I remember we discussed the importance of point-to-point links in RSTP, but I'm not sure if it applies here.
upvoted 0 times
...

Save Cancel