MENU
SIMULATION
All physical cabling between the two switches is installed. Configure the network connectivity between the switches using the designated VLANs and interfaces.
1. Configure VLAN 100 named Compute and VLAN 200 named Telephony where required for each task.
2. Configure Ethernet0/1 on SW2 to use the existing VLAN named Available.
3. Configure the connection between the switches using access ports.
4. Configure Ethernet0/1 on SW1 using data and voice VLANs.
5. Configure Ethemet0/1 on SW2 so that the Cisco proprietary neighbor discovery protocol is turned off for the designated interface only.
Suggested Answer: A
Get Premium 200-301 Questions
as Interactive Web-Based Practice Test or PDF
Real Exam Format
Detailed Explanations
Instant Access
Get Your Practice Test
Answer as below configuration:
on sw1
enable
conf t
vlan 100
name Compute
vlan 200
name Telephony
int e0/1
switchport voice vlan 200
switchport access vlan 100
int e0/0
switchport mode access
do wr
on sw2
Vlan 99
Name Available
Int e0/1
Switchport access vlan 99
do wr
31 comments · newest first
CA
Carmelina
11 months ago
I thought Ethernet0/1 on SW1 needed to be trunked, not access.
FA
Fairy
11 months ago
Don't forget to set the access ports correctly for the switches!
AR
Ardella
11 months ago
Wait, why are we turning off neighbor discovery on SW2? Seems odd.
LE
Lenita
11 months ago
Totally agree, those VLANs are essential for traffic separation!
CA
Carey
12 months ago
VLAN 100 is for Compute, and VLAN 200 is for Telephony.
LO
Loren
12 months ago
I practiced a similar scenario, but I can't recall if I need to specify the trunking mode for the connection between the switches.
AS
Ashleigh
1 year ago
I think I got the VLANs down, but I'm not completely confident about disabling the neighbor discovery protocol on just one interface.
KI
Kirk
1 year ago
This question feels similar to one we did in class about configuring access ports. I think I need to double-check the syntax for the access port commands.
JI
Jill
1 year ago
I remember practicing VLAN configuration, but I'm a bit unsure about the exact commands for naming them.
LY
Lynelle
1 year ago
Wait, what's this about turning off the Cisco proprietary neighbor discovery protocol on Ethernet0/1 of SW2? I'll need to research that a bit before I attempt it.
RY
Ryan
1 year ago
No problem, I've got this. I'll configure Ethernet0/1 on SW2 to use the existing VLAN named Available, and then set up the inter-switch connection using access ports. Easy peasy.
GO
Goldie
1 year ago
Hmm, I'm a bit confused about the part where it says to configure the connection between the switches using access ports. I'll need to double-check the VLAN requirements for that.
VE
Veta
1 year ago
Okay, this looks like a pretty straightforward VLAN and interface configuration question. I'll start by creating the required VLANs and naming them as specified.
VE
Veronica
2 years ago
This looks like a nice, juicy configuration question. Time to put my networking skills to the test!
GI
Gilbert
2 years ago
Haha, I bet the exam writers just threw in that Cisco protocol thing to trip us up. Nice try, but I'm on to you!
KE
Keena
2 years ago
Let's make sure we double-check everything to be safe.
OT
Otis
2 years ago
Yeah, but we're prepared for anything they throw at us.
TA
Tamera
2 years ago
I know right, they always try to trick us with those tricky details.
SH
Shayne
2 years ago
Wait, we need to turn off the Cisco neighbor discovery protocol on Ethernet0/1 on SW2? That's a bit random, but okay, I'll make sure to do that.
FR
Freeman
2 years ago
Micaela: I'll keep that in mind, thanks for the reminder.
AL
Alexia
2 years ago
User 3: Make sure to follow all the steps for configuring the network connectivity between the switches.
MI
Micaela
2 years ago
User 2: Yeah, that's a specific requirement for that interface.
CH
Chandra
2 years ago
User 1: Did you see we need to turn off the Cisco neighbor discovery protocol on Ethernet0/1 on SW2?
RO
Rosalyn
2 years ago
Hmm, seems straightforward. Just need to configure the VLANs and interfaces correctly. Should be able to knock this one out.
YU
Yuriko
2 years ago
Steffanie: After that, we can configure Ethernet0/1 on SW1 using data and voice VLANs.
KA
Kattie
2 years ago
User 3: Next, we need to configure the connection between the switches using access ports.
ST
Steffanie
2 years ago
User 2: Got it. I'll also configure Ethernet0/1 on SW2 to use the existing VLAN named Available.
TA
Tanesha
2 years ago
User 1: Let's start by configuring VLAN 100 named Compute and VLAN 200 named Telephony.
GA
Gail
2 years ago
I believe we should turn off the Cisco proprietary neighbor discovery protocol on SW2.
KI
Kina
2 years ago
I agree, we also need to configure the connection between the switches using access ports.
NI
Nina
2 years ago
I think we need to configure VLANs 100 and 200 for this task.