Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 200-301 Exam - Topic 4 Question 73 Discussion

Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured1. Configure an LACP EtherChannel and number it as 1; configure it between switches SW1 and SVV2 using interfaces Ethernet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends2 Configure the EtherChannel as a trunk link.3. Configure the trunk link with 802.1 q tags.4. Configure the native VLAN of the EtherChannel as VLAN 15.
A) See the Explanation below

Cisco 200-301 Exam - Topic 4 Question 73 Discussion

Actual exam question for Cisco's 200-301 exam
Question #: 73
Topic #: 4
[All 200-301 Questions]

Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured

1. Configure an LACP EtherChannel and number it as 1; configure it between switches SW1 and SVV2 using interfaces Ethernet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends

2 Configure the EtherChannel as a trunk link.

3. Configure the trunk link with 802.1 q tags.

4. Configure the native VLAN of the EtherChannel as VLAN 15.

Show Suggested Answer Hide Answer
Suggested Answer: A

Answer as below configuration:

On SW1:

conf terminal

vlan 15

exit

interface range eth0/0 - 1

channel-group 1 mode active

exit

interface port-channel 1

switchport trunk encapsulation dot1q

switchport mode trunk

switchport trunk native vlan 15

end

copy run start

on SW2:

conf terminal

vlan 15

exit

interface range eth0/0 - 1

channel-group 1 mode active

exit

interface port-channel 1

switchport trunk encapsulation dot1q

switchport mode trunk

switchport trunk native vlan 15

end

copy run start


by Carin at Oct 07, 2023, 12:23 AM

Limited Time Offer

25%

Off

Get Premium 200-301 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Gianna
9 months ago
Sounds good, but I prefer static EtherChannels for simplicity.
upvoted 0 times
...
Chery
10 months ago
Trunking with 802.1Q tags is essential for VLANs!
upvoted 0 times
...
Arletta
10 months ago
Wait, why VLAN 15? Isn't that a bit unusual?
upvoted 0 times
...
Ashleigh
10 months ago
Totally agree, but make sure the modes match!
upvoted 0 times
...
Nina
10 months ago
LACP EtherChannel is a great way to increase bandwidth!
upvoted 0 times
...
Ellen
10 months ago
I remember the concept of matching LACP modes, but I can't quite remember if it was active or passive that we used in our last practice.
upvoted 0 times
...
Meghann
11 months ago
I feel confident about configuring the native VLAN, but I might mix up the interface numbers. Was it Ethernet0/0 and Ethernet0/1 on both switches?
upvoted 0 times
...
Herschel
11 months ago
I think we did a similar question where we had to set up trunk links with 802.1Q. I just need to recall the syntax for that.
upvoted 0 times
...
Josephine
11 months ago
I remember we practiced configuring LACP EtherChannels, but I'm a bit unsure about the exact commands for setting the mode.
upvoted 0 times
...
Dortha
11 months ago
This seems pretty straightforward. I'm confident I can knock this out as long as I take my time and follow the steps carefully.
upvoted 0 times
...
Carrol
11 months ago
Wait, I'm a little confused about the 802.1q tagging part. I'll need to double-check the details on that in my notes.
upvoted 0 times
...
Kip
11 months ago
No problem, I've done this kind of thing before. Just need to remember the specific commands for setting up the trunk link and native VLAN.
upvoted 0 times
...
Aliza
11 months ago
Okay, this looks like a pretty straightforward Layer 2 configuration question. I think I can handle this if I just take it step-by-step.
upvoted 0 times
...
Bette
11 months ago
Hmm, configuring an LACP EtherChannel between two switches - that's something I haven't practiced much. I'll need to make sure I get the interface names and LACP mode right.
upvoted 0 times
...
Quiana
11 months ago
I'm pretty sure the answer is 7 mmol/L, that's the standard diagnostic threshold for type 2 diabetes.
upvoted 0 times
...
Ronald
11 months ago
Okay, I've got this. The new admin needs to manage security, dimensions, business rules, and data loading for the CapEx app, but not any other applications. So the two valid roles would be A) Administrator for the CapEx application and E) Dimension Editor for the CapEx dimensions.
upvoted 0 times
...

Save Cancel