Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 200-301 Exam - Topic 2 Question 94 Discussion

Refer to the exhibit.An engineer configures interface fa0/1 on SW1 and SW2 to pass traffic from two different VLANs. For security reasons, company policy requires the native VLAN to be set to a nondefault value. Which configuration meets this requirement?A)B)C)D)
D) Option D
A) Option A
B) Option B
C) Option C

Cisco 200-301 Exam - Topic 2 Question 94 Discussion

Actual exam question for Cisco's 200-301 exam
Question #: 94
Topic #: 2
[All 200-301 Questions]

Refer to the exhibit.

An engineer configures interface fa0/1 on SW1 and SW2 to pass traffic from two different VLANs. For security reasons, company policy requires the native VLAN to be set to a nondefault value. Which configuration meets this requirement?

A)

B)

C)

D)

Show Suggested Answer Hide Answer
Suggested Answer: D

Topic 5, Simulations / Lab


by Verda at Sep 16, 2024, 09:34 AM

Limited Time Offer

25%

Off

Get Premium 200-301 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Bobbie
9 months ago
All options look good, but I’m leaning towards B.
upvoted 0 times
...
Mollie
9 months ago
I disagree, Option A seems more secure.
upvoted 0 times
...
Melvin
10 months ago
Wait, is it really that important to change the native VLAN?
upvoted 0 times
...
Brigette
10 months ago
I think Option C looks right.
upvoted 0 times
...
Heike
10 months ago
Native VLAN should definitely be nondefault for security.
upvoted 0 times
...
Trinidad
10 months ago
I’m a bit confused about the syntax in the options. I hope I can recognize the correct command when I see it during the exam.
upvoted 0 times
...
Penney
11 months ago
I know that the native VLAN should not be set to 1, but I can't remember if option C specifies a different VLAN.
upvoted 0 times
...
Annett
11 months ago
I think we practiced a similar question where we had to configure trunk ports. I feel like option B might be the right choice, but I'm not entirely sure.
upvoted 0 times
...
Mitzie
11 months ago
I remember we discussed the importance of changing the native VLAN for security, but I can't recall which option actually does that.
upvoted 0 times
...
Madalyn
11 months ago
I'm pretty confident I can solve this. The non-default native VLAN requirement is the giveaway. I just need to double-check the options to make sure I'm selecting the right one.
upvoted 0 times
...
Alfred
11 months ago
Okay, I think I've got this. The key is to identify the configuration that sets the native VLAN to a non-default value while still passing traffic from two different VLANs. Let me go through the options carefully.
upvoted 0 times
...
Dustin
11 months ago
Hmm, I'm a bit confused by the exhibit. I'll need to review the VLAN configuration concepts to make sure I understand what's being asked here.
upvoted 0 times
...
Reed
11 months ago
This looks like a VLAN configuration question. I'll need to carefully examine the exhibit and the options to determine which one meets the requirement of setting the native VLAN to a non-default value.
upvoted 0 times
...
Tyra
11 months ago
This is a tricky one, but I think I can figure it out. I'll start by analyzing the exhibit and then systematically go through the answer choices to find the one that meets the stated requirement.
upvoted 0 times
...
Monte
2 years ago
Hmm, Option D seems a bit overkill. Why create a new VLAN when you can just change the native VLAN on the existing ones? Option C is the way to go.
upvoted 0 times
...
Loreta
2 years ago
Haha, this is a classic networking question. I bet the answer is Option C, because who doesn't love a good non-default VLAN setting?
upvoted 0 times
...
Samira
2 years ago
I'm going with Option B. It's simple and gets the job done without any unnecessary complications.
upvoted 0 times
Shawnee
2 years ago
Yeah, Option B seems like the most straightforward and secure option here.
upvoted 0 times
...
Ailene
2 years ago
I think Option C might also work well, but Option B is definitely a solid choice.
upvoted 0 times
...
Deane
2 years ago
I agree, Option B looks like the best choice for this scenario.
upvoted 0 times
...
...
Stephen
2 years ago
Hmm, you might be right. I'll reconsider my answer.
upvoted 0 times
...
Kayleigh
2 years ago
I disagree, I believe Option B is the right choice because it sets the native VLAN to a nondefault value.
upvoted 0 times
...
Lashaun
2 years ago
Option C looks good to me. Setting the native VLAN to a non-default value is a straightforward way to meet the security requirement.
upvoted 0 times
Roslyn
2 years ago
Sounds good, let's implement Option C for the VLAN setup.
upvoted 0 times
...
Ilene
2 years ago
Option C it is then, let's go with that configuration.
upvoted 0 times
...
Pedro
2 years ago
I agree, setting the native VLAN to a non-default value is a good security measure.
upvoted 0 times
...
Moon
2 years ago
I think Option C is the best choice.
upvoted 0 times
...
...
Stephen
2 years ago
I think the correct configuration is Option C.
upvoted 0 times
...

Save Cancel