Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

CheckPoint 156-582 Exam - Topic 7 Question 9 Discussion

After deploying a new Static NAT configuration, traffic is not getting through. What command would you use to verify that the proxy ARP configuration has been loaded?
B) fw ctl arp
A) fw ctl conn
C) fw arp ctl
D) cp ctl arp

CheckPoint 156-582 Exam - Topic 7 Question 9 Discussion

Actual exam question for CheckPoint's 156-582 exam
Question #: 9
Topic #: 7
[All 156-582 Questions]

After deploying a new Static NAT configuration, traffic is not getting through. What command would you use to verify that the proxy ARP configuration has been loaded?

Show Suggested Answer Hide Answer
Suggested Answer: B

To verify the Proxy ARP configuration after deploying a new Static NAT setup, the fw ctl arp command is used. This command displays the current ARP table entries, allowing administrators to confirm that the proxy ARP entries corresponding to the Static NAT mappings have been correctly loaded and are active.


by Susana at Mar 06, 2025, 10:14 AM

Limited Time Offer

25%

Off

Get Premium 156-582 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Colene
9 months ago
Just to clarify, B is definitely the command to check proxy ARP.
upvoted 0 times
...
Micah
9 months ago
I heard C is a common mistake.
upvoted 0 times
...
Benedict
10 months ago
Wait, are we sure about that?
upvoted 0 times
...
Malcolm
10 months ago
Totally agree, B is the right one!
upvoted 0 times
...
Jani
10 months ago
I think it's B, fw ctl arp.
upvoted 0 times
...
Herman
10 months ago
I’m a bit confused; I thought there was a command that started with "cp" for ARP, but I can't recall if it’s option D or not.
upvoted 0 times
...
Holley
10 months ago
I feel like I’ve seen the command "fw ctl arp" before in my notes, so that could be the right answer.
upvoted 0 times
...
Lon
11 months ago
I remember practicing a question similar to this, and I think the command to verify proxy ARP is definitely not option C.
upvoted 0 times
...
Beula
11 months ago
I think we might need to check the ARP settings, so maybe it's option B, but I'm not completely sure.
upvoted 0 times
...
Lashawn
11 months ago
Hmm, this is a tricky one. I think the key is to focus on the "proxy ARP" part of the question. That's likely the specific configuration we need to verify, so the command would be something related to ARP, not just general firewall connections.
upvoted 0 times
...
Adelaide
11 months ago
I'm a bit confused on this one. I'm not sure if the question is asking about the ARP table in general or specifically the proxy ARP configuration. I'll have to think it through carefully.
upvoted 0 times
...
Vernice
11 months ago
I've got this! The command to verify the proxy ARP configuration is fw ctl arp. I'm pretty confident that's the right answer.
upvoted 0 times
...
Isadora
11 months ago
Okay, let's see. I know there's a command to check the ARP table, but I'm not sure if that's the same as verifying the proxy ARP configuration. I'll have to review my notes on that.
upvoted 0 times
...
Han
11 months ago
Hmm, this seems like a tricky one. I'll need to think through the different firewall commands carefully to figure out the right one for verifying the proxy ARP configuration.
upvoted 0 times
...
Gabriele
1 year ago
I believe fw ctl arp is the correct command because it specifically checks the ARP configuration.
upvoted 0 times
...
France
1 year ago
I'm not sure, but I think A) fw ctl conn could also be used to verify the configuration.
upvoted 0 times
...
Jani
1 year ago
I agree with Francoise, fw ctl arp makes sense to check the proxy ARP configuration.
upvoted 0 times
...
Ming
1 year ago
D) cp ctl arp sounds like it could be the answer, but I'm not feeling too confident about that one. Proxy ARPs, am I right?
upvoted 0 times
...
Virgilio
1 year ago
I'm gonna go with B) fw ctl arp. Might as well check the ARP table, maybe there's a typo in there or something.
upvoted 0 times
Stanton
1 year ago
User3: I'll run fw ctl arp and see what comes up.
upvoted 0 times
...
Ariel
1 year ago
User2: Yeah, that's a good idea. Maybe we missed something there.
upvoted 0 times
...
Breana
1 year ago
User1: I think you're right, let's check the ARP table.
upvoted 0 times
...
...
Mozell
1 year ago
B) fw ctl arp sounds right to me. Gotta love those proxy ARPs, they're the glue that holds the internet together!
upvoted 0 times
Royce
1 year ago
D) cp ctl arp
upvoted 0 times
...
Gilma
1 year ago
C) fw arp ctl
upvoted 0 times
...
Christiane
1 year ago
B) fw ctl arp
upvoted 0 times
...
Peggie
1 year ago
A) fw ctl conn
upvoted 0 times
...
...
Penney
2 years ago
I think the answer is B) fw ctl arp. It's the only one that mentions verifying the proxy ARP configuration.
upvoted 0 times
Portia
1 year ago
User 2: Yeah, that makes sense. It's the only one that mentions verifying the proxy ARP configuration.
upvoted 0 times
...
Phung
1 year ago
User 1: I think the answer is B) fw ctl arp.
upvoted 0 times
...
...
Francoise
2 years ago
I think the answer is B) fw ctl arp.
upvoted 0 times
...

Save Cancel