Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

APICS Exam CPIM-ECO Topic 3 Question 91 Discussion

Actual exam question for APICS's CPIM-ECO exam
Question #: 91
Topic #: 3
[All CPIM-ECO Questions]

Group technology identifies the common characteristics of parts on the basis of which of the following factors?

Show Suggested Answer Hide Answer
Suggested Answer: B

by Cary at Jun 29, 2024, 01:24 AM

Limited Time Offer

25%

Off

Get Premium CPIM-ECO Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Dorothea
12 months ago
Hmm, I'd say B) Processes. Anything else would just be weird, like grouping parts by how much they cost to make or where they came from. Processes is the way to go.
upvoted 0 times
...
Stefan
12 months ago
B) Processes, no doubt. Unless the parts are magically appearing out of thin air, the manufacturing process is key to group technology.
upvoted 0 times
Mitsue
11 months ago
C) Source is also a factor to consider, where the parts come from can impact the manufacturing process.
upvoted 0 times
...
Shenika
11 months ago
D) Costs are important as well, you need to optimize the production to minimize expenses.
upvoted 0 times
...
Lorrie
11 months ago
A) Yields play a role too, you need to consider how much output you can get from each part.
upvoted 0 times
...
Stephaine
11 months ago
B) Processes, no doubt. Unless the parts are magically appearing out of thin air, the manufacturing process is key to group technology.
upvoted 0 times
...
...
Ozell
1 years ago
I'm going with B) Processes. Although I did consider costs, because who doesn't love saving money? But processes make the most sense for this question.
upvoted 0 times
...
Jade
1 years ago
B) Processes, for sure. Group technology is all about streamlining production, and that's all about the processes used to make the parts.
upvoted 0 times
Eden
10 months ago
Processes play a huge role in identifying common characteristics of parts.
upvoted 0 times
...
Alaine
10 months ago
Definitely, understanding the processes is crucial for efficient production.
upvoted 0 times
...
Alecia
10 months ago
I agree, processes are key in group technology.
upvoted 0 times
...
Joaquin
10 months ago
C) Source can also be important, but ultimately it's about optimizing processes for efficiency.
upvoted 0 times
...
Carry
11 months ago
A) Yields play a role too, but I agree that processes are the main focus in group technology.
upvoted 0 times
...
Dana
11 months ago
B) Processes are definitely key in group technology. It helps identify the common characteristics of parts.
upvoted 0 times
...
...
Jovita
1 years ago
I would go with source as the factor for grouping parts.
upvoted 0 times
...
Tanesha
1 years ago
Definitely B) Processes. How else would you group parts with common characteristics? Yields, sources, and costs are just byproducts of the manufacturing process.
upvoted 0 times
Eun
12 months ago
Yes, processes are what determine the common characteristics of parts.
upvoted 0 times
...
Corrinne
1 years ago
I agree, B) Processes is the key factor in grouping parts.
upvoted 0 times
...
...
Paris
1 years ago
I think it's yields that determine the common characteristics.
upvoted 0 times
...
Tony
1 years ago
I think the answer is B) Processes. Group technology groups parts based on their manufacturing processes, not their yields, sources, or costs.
upvoted 0 times
Fatima
1 years ago
Yes, that's correct. It helps in identifying common characteristics to improve efficiency.
upvoted 0 times
...
Shoshana
1 years ago
I agree, group technology focuses on grouping parts based on their manufacturing processes.
upvoted 0 times
...
...
Clay
1 years ago
I believe it's costs that are considered.
upvoted 0 times
...
Cornell
1 years ago
I think it's based on processes.
upvoted 0 times
...

Save Cancel