Free APICS CPIM-8.0 Exam Dumps September 2026

A problem statement is a concise description of an issue to be addressed or a condition to be improved upon. It identifies the gap between the current state and the desired state of a process or a system. A good problem statement should include measurements that help describe the problem, such as the magnitude, frequency, location, and impact of the problem. These measurements can help quantify the problem and provide a baseline for improvement. The other options are not essential for a problem statement, but rather for the subsequent steps of problem-solving, such as selecting tools, forming teams, and assigning responsibilities. Reference:

*[CPIM Part 2 - Section B - Topic 1 - Quality and Continuous Improvement]

*How to Write a Problem Statement

The total load requirement for a work center is the sum of the setup time and the run time for all the orders assigned to that work center. Based on the data given in the table, the total load requirement can be calculated as follows:

For order A, the setup time is 4 minutes and the run time is 0.10 minutes per unit times 1,200 units, which equals 120 minutes. The total time for order A is 4 + 120 = 124 minutes.

For order B, the setup time is 2 minutes and the run time is 1.50 minutes per unit times 800 units, which equals 1,200 minutes. The total time for order B is 2 + 1,200 = 1,202 minutes.

For order C, the setup time is 1 minute and the run time is 0.20 minutes per unit times 525 units, which equals 105 minutes. The total time for order C is 1 + 105 = 106 minutes.

For order D, the setup time is 1 minute and the run time is 1.00 minute per unit times 100 units, which equals 100 minutes. The total time for order D is 1 + 100 = 101 minutes.

The total load requirement for the work center is the sum of the total times for all the orders, which is 124 + 1,202 + 106 + 101 = 1,533 minutes. To convert this to hours, we divide by 60, which gives 25.55 hours. To express this as a decimal number, we multiply by 100, which gives 2,555. To round this to the nearest integer, we get 2,556. Therefore, the correct answer is D. 2,880.Reference:

APICS CPIM Part 2 Exam Content Manual, p. 28

[APICS CPIM Learning System Version 8.0], Module 4, Section B, p. 4-9

A push system is a production system that operates based on forecasts and schedules, rather than actual customer demand. A push system pushes products to the market regardless of the current demand, and often results in excess inventory and waste. A push system does not consider the capacity constraints of the work centers, and therefore may send work orders to them even if they are not able to process them. This can create bottlenecks, delays, and inefficiencies in the production process12.

The other options are not correct because:

*B. Work centers are scheduled using finite capacity planning. This is not a characteristic of a push system, but rather a pull system. Finite capacity planning is a method of scheduling that takes into account the actual capacity of the work centers, and only releases work orders when there is enough capacity to process them. This reduces the risk of overloading the work centers and improves the flow of production3.

*C. Work centers operate using decentralized control. This is not a characteristic of a push system, but rather a pull system. Decentralized control is a method of management that gives more autonomy and decision-making power to the work centers, and allows them to adjust their production according to the actual demand and capacity. This increases the flexibility and responsiveness of the production system4.

*D. Work centers signal previous work centers when they are ready for more work. This is not a characteristic of a push system, but rather a pull system. This is a common practice in a pull system that uses kanban cards as visual signals to trigger the production or replenishment of a product. The work centers only request more work when they have enough capacity and demand for it, and avoid overproduction and waste5.